Zev .300 sights lower 1/4th co-witness with Rm06(NO sealing plate)

Complete build list: -Cerakote done by MCM Firearms. -Frame work by myself(modified G4,G22). -Jagerwerks Yeti slide w/rmr cut. -S3f solutions stock length G22 40-9mm barrel threaded by grumpy's guns. -S3f solutions stock length G22 .40cal barrel threaded by grumpy's guns. -Lone Wolf Locking Block LWD-1447. -Ghost Inc Rocket 3.5lb connector. -Wolff self-defense spring kit. -NDZ Gen4,gen3 style recoil rod(modified). -NDZ Extended Slide Lock Lever. -NDZ Adjustable trigger housing. -L2D Stainless Steel nitride Pin Set. -L2D Ultimate lightweight fluted striker. -L2D Enhanced Firing Pin Safety . -Bastion aluminum extended mag release. -RYG phantom adjustable trigger. -The glockmeister 9mm extractor. -The glockmeister .40cal extractor. -Trijicon FDE RMR Type 2 RM06 -Zev .300 suppressor sights. -kagwerks extended slide release. -Agency Arms gen4 Magwell(NBS).

These are zev .300 sights, they are veryminimalist as far as presentation throughthe rmr06. But they are usable. My main focus is the red dot(which is why I had thermr before the rear sight) and that it is clear of distraction. Zev .300 sights may not be the go to choose for most, but it works for me. (I am not running a sealing plate)

The finished product has arrived!!!!!  This has been an awesome 2 year project in the works and I'm glad I could bring it tolight for the past 4 months of its final steps. MCM firearms did an outstanding job withthe cerakote, and Grumpy's guns did anabsolutely beautiful job threading the stock length S3F G22 9mm conversion glock barrel. I hope that other will enjoy my posts and see what is possible. Thank you everyone for all your support throughout this truly custombuild.

Just got my slide back from jagerwerks. I chose the "yeti" milling option with the rmr cut behind my rear sight. I'm honestly not sure I will ever use my ZEV .300 high irons but they are still there just in case. The stock length Glock 22 barrel I had threaded by grumpys guns out of Texas. He does beautiful work. Everything has been shipped off to mcm firearms out of Nampa Idaho to be cerakoted Kryptek Mandrake. I will post again when it's all back to me and assembled☺

Left to right -g23, g23x, g22. As you can see, the middle and right are both g17/22 frames. The material before the rails has been removed and the rails have been rounded on the muzzle end to contour with the slide. Lastly the front of the frame rail has been cut back to mock the g23 length.

Is off a couple thousands on one side but it's close enough for me. It's going to have a tlr1s mounted to it and the difference won't be noticed.

Update: I was not happy with the front of the frame.I sacrificed the G22 frame to create a flat plane. I used rubber spacers to protect the slide and large vice grips(a vice is a better alternative). Then I used 400 grithe wrapped around a flat file and sanded using the flat front of the slide as my guide. I then finished it off with 1200 and 2000.

It will be here Saturday. I ordered a stock length G22 S3F 40-9😍 #glock23x

Just 3 mods make it happen, shave back the area before the front rails, cut down a gen4 gen3 style recoil rod from NDZ proformance and cut the front rail back to 19/23 length. Uses a stock g22 barrel. I'm sending a stock length g22 and stock length g22 40-9 barrel in to be threaded to complete my modular build. Benefits to the gen 4 22 frame is larger barrel locking lug and stronger locking block, a truly timed/tuned slide travel, uses any mags without a mod and lots of aftermarket parts available.